Ceramic Ball Mill

Ceramic Ball Mill is the core low-contamination grinding equipment in new materials, electronics, ceramics, and pharmaceutical industries. It is suitable for grinding high-purity materials such as zirconia, alumina, and quartz, as well as special material processing, such as electronic ceramics. It has a smooth inner wall, uniform grinding effect, and easy cleaning. It is used as key equipment for fine grinding in high-purity powder production lines, and can be equipped with ceramic liners and grinding media for pollution-free operation.

When selecting the model, it is necessary to optimize the configuration according to the material purity requirements (such as φ1200×2400 is suitable for electronic grade zirconia, φ500×500 is suitable for small-batch pharmaceutical materials) and grinding fineness (such as acid-resistant ceramic lining for corrosive materials). In the future, it will develop in the direction of precision control and energy saving, and further improve grinding uniformity and material purity retention.

Products Display

High-hardness ceramic materials (alumina, zirconia, etc.) with ultra-fine fineness (1-5μm)

Material characteristics: Mohs hardness ≥8, high brittleness, strict particle size distribution, zero metal contamination allowed

Ceramic Ball Mill selection recommendations:

• Model selection: φ1200×2400 and above large models are preferred

• Grinding media: high-purity zirconia balls (φ3-5mm) with HRA ≥88

• Speed adjustment: set rotational speed to 60-70rpm for slow and precise grinding
Medium-hard ceramic materials (cordierite, glass powder, etc.) with fine fineness (5-50μm)

Material characteristics: Mohs hardness 4-7, good grindability, moderate particle uniformity requirement

Optimization plan:

• Model selection: φ500×500-φ1000×2000 series can meet most needs

• Media configuration: mix φ8-12mm alumina balls and zirconia balls in 2:1 ratio

• Efficiency improvement: increase rotational speed to 80-100rpm and extend grinding time by 10%

Material Application

High-hardness industrial materials (Mohs hardness ≥6)

Typical materials: ▸ Quartz sand (high abrasiveness) ▸ Alumina powder (hardness 9, high purity requirement) ▸ Silicon carbide (hardness 9.5, strong wear resistance) ▸ Zirconium silicate (hardness 7.5, stable chemical properties)

Application scenarios: Raw material grinding in ceramic glaze production, abrasive powder processing in hardware industry, high-purity filler preparation in electronic component manufacturing, wear-resistant coating material grinding

Medium-hardness industrial materials (Mohs hardness 3-5)

Typical materials: ▸ Calcium carbonate (hardness 3, low impurity content) ▸ Talc powder (hardness 1-2, good lubricity) ▸ Gypsum powder (hardness 2, easy to grind) ▸ Kaolin (hardness 2-2.5, high whiteness)

Application scenarios: Filler grinding in plastic/rubber industry, additive processing in paint production, auxiliary material preparation in daily chemical industry, ceramic body raw material grinding in building ceramics sector

specification

*The output will vary according to different materials, feed particle size and other factors

Model	Capacity(t/h)	Rotate speed(r/min)	Grinding Balls(t)	Motor Power(kw)	Gear box
Model	Capacity(t/h)	Rotate speed(r/min)	Grinding Balls(t)	Motor Power(kw)	Model	Speed Ratio
Ф1.2x4.5	1.6-5.8	30.3	5	55	ZD30	4.5
Ф1.5x5.7	3.5-6	26.34	11	130	ZD40	4
Ф1.83x6.4	6.5-15	23.9	21	210	ZD60	4.5
Ф1.83x7	7.5-17	24.5	23	245	ZD60	4.5
Ф2.2x6.5	14-20	21.4	31	280	ZD70	5
Ф2.4x7	17-28	20.4	39	380	ZD80	5
Ф2.4x8	20-35	20.3	42	570	ZD80	5
Ф2.4x12	35-45	20	63	800	MBY710	6.3
Ф2.4x13	35-38	19.4	68	800	MBY710	6.3
Ф2.6x13	40-55	19.5	82	1000	JDX800	6.3
Ф3x9	50-55	18.34	78	1000	JDX800	6.3
Ф3.2x9	60-70	17.6	95	1250	MBY900	7.1
Ф3.5x11	75-85	16.8	150	1250	JDX900	5.84
Ф3.8x12	85-110	17	175	1600	MBY800	5.6
Ф4.6x10+3.5	180-210	15	278	3550	JQS3500	15.1

Menu

≤25mm

18.5-800KW

0.65–90 t/h

Products Display

High-hardness ceramic materials (alumina, zirconia, etc.) with ultra-fine fineness (1-5μm)

Ceramic Ball Mill selection recommendations:

Medium-hard ceramic materials (cordierite, glass powder, etc.) with fine fineness (5-50μm)

Optimization plan:

Material Application

High-hardness industrial materials (Mohs hardness ≥6)

Medium-hardness industrial materials (Mohs hardness 3-5)

specification

Contacts and Support

Hotline

WhatsApp

Products

please contact us

Menu

Ceramic Ball mill

≤25mm

18.5-800KW

0.65–90 t/h

Products Display

High-hardness ceramic materials (alumina, zirconia, etc.) with ultra-fine fineness (1-5μm)

Ceramic Ball Mill selection recommendations:

Medium-hard ceramic materials (cordierite, glass powder, etc.) with fine fineness (5-50μm)

Optimization plan:

Material Application

High-hardness industrial materials (Mohs hardness ≥6)

Medium-hardness industrial materials (Mohs hardness 3-5)

specification

Product Recommendation